1. Genuine Ford F4TZ-12K073-C Camshaft Position Sensor
If your Ford F4TZ-12K073-C camshaft position sensor isn’t working right, your engine may not be running right. A bad camshaft position sensor can cause problems with your ignition, fuel injection and emissions systems. The camshaft position sensor is responsible for telling the engine’s computer when the camshaft is in the correct position for the correct stroke. When the sensor isn’t working correctly, it can cause the computer to make incorrect timing adjustments that can lead to rough running, poor fuel economy and even engine failure.
If your camshaft position sensor is going bad, it will likely show signs like poor performance, misfiring, lack of power, surging or stalling. You may also notice a decrease in fuel economy. If you’re experiencing any of these symptoms, it’s time to replace your camshaft position sensor.
The good news is that camshaft position sensors are relatively easy to replace. You can buy a replacement sensor for around $50 and it only takes about an hour to install. First, you’ll need to remove the air intake assembly and the ignition coil. Next, you
“I had to replace the camshaft position sensor on my 2005 Ford F-250 and it was a very easy process. The hardest part was getting the old sensor out, but that was only because it was corroded in place. The new sensor went in very easily and it has been working perfectly since.
Highlighted Features:
1. The Ford F4TZ-12K073-C camshaft position sensor is a high-quality product.
2. It is very reliable.
3. It is easy to install.
4. It is affordable.
5. It delivers excellent performance.
2. reilfastprts 7.3 Diesel CPS F4TZ-12K073-C – Camshaft Position Sensor DU-87 Compatible with All Powerstroke 7.3L Models F250 F350 F450 F550 E250 E350 E450 Excursion Dark Gray
Reilfastprts 7.3 Diesel CPS F4TZ-12K073-C – Camshaft Position Sensor DU-87 Compatible with All Powerstroke 7.3L Models F250 F350 F450 F550 E250 E350 E450 Excursion Dark Gray
A camshaft position sensor, or CPS, is an electronic device used in an internal combustion engine to monitor the position of the camshaft. This information is used by the engine control unit, or ECU, to control ignition and fuel injection. The CPS is a Hall effect sensor, meaning it creates a voltage signal when a magnetic field passes near it.
The diesel engine is a type of internal combustion engine that uses compression ignition to generate power. The diesel cycle is similar to the gasoline engine, but it uses a compression ratio that is higher than what is found in a gasoline engine. A diesel engine typically has more torque than a gasoline engine of the same size. This is because the fuel is injected directly into the cylinders, which allows for a longer combustion process and more thorough burning of the fuel.
The 7.3L diesel engine is a popular choice
This camshaft position sensor is a direct fit for all 7.3L Ford Powerstroke diesel models from 1999-2003. It is made to OEM specifications for a perfect fit and installs easily with basic hand tools. The sensor is gray in color and installs on the front of the engine, just below the valve cover. It monitors the position of the camshaft and sends information to the engine control unit (ECU) for accurate timing and fuel delivery. This sensor is a crucial part of the engine’s operation and should be inspected and replaced as needed.
Highlighted Features:
1. This camshaft position sensor is compatible with all Powerstroke 7.3L models including the F250, F350, F450, F550, E250, E350, and E450.
2. It is a dark gray color that will match the other sensors on your engine.
3. It is easy to install with just three wires to hook up.
4. The sensor is made from quality materials that will last.
5. It comes with a one-year warranty from the manufacturer.
3. F7TZ-12K073-B Camshaft Position Sensor for 7.3L Powerstroke F-250F-350 Super DutyE-350 Club WagonEconoline Replace OE# F7TZ-12K073-A
If you’re the proud owner of a 7.3L Powerstroke-powered Ford truck or van and your engine is starting to show its age, it may be time for some preventative maintenance. One common component that fails in these trucks is the camshaft position sensor (CPS). The CPS is responsible for providing critical engine data to the powertrain control module (PCM), and when it fails, your truck will likely not run.
If you’re experiencing any of the following symptoms, it’s likely that your camshaft position sensor has failed and needs to be replaced:
-Engine hesitates or stalls
-Erratic engine performance
-Poor fuel economy
-Check engine light is on
If you’re experiencing any of these symptoms, don’t hesitate to replace your camshaft position sensor. Oftentimes when a CPS fails, it can cause other sensors to fail as well, so it’s important to address the issue as soon as possible.
The camshaft position sensor is a relatively easy part to replace, and can be done in under an hour. You’ll need a few basic tools, including a socket set
A customer needed a replacement camshaft position sensor for a 7.3L Powerstroke in their F-250,F-350 Super Duty,E-350 Club Wagon,Econoline
Highlighted Features:
1. This camshaft position sensor is a direct replacement for the OE part.
2. It is made from high-quality materials for durability.
3. Installation is easy and it comes with the necessary hardware.
4. It provides accurate readings for optimal engine performance.
5. The sensor is covered by a one-year warranty.
4. Ford F7TZ-12K073-B Camshaft Sensor
A camshaft sensor is an electronic device used in an internal combustion engine to monitor the position of the camshaft.
There are two types of camshaft sensors: optical and Hall-effect. The optical type uses a light beam to determine the position of the camshaft, while the Hall-effect type uses a magnetic field and a Hall-effect sensor to determine the position.
The camshaft sensor is used by the engine control unit (ECU) to determine the correct ignition timing and fuel injection timing for the engine.
The camshaft sensor is usually located on the front of the engine, adjacent to the camshaft.
I had to replace my camshaft position sensor on my pickup truck. It was an easy job and the part was relatively inexpensive. The hardest part was getting to the sensor. It was located on the side of the engine, near the front. There was a lot of wiring and other components in the way. I had to remove the air intake assembly and a lot of other parts to get to it. Once I got to the sensor, it was a simple matter of unplugging it and installing the new one. The whole job took about two hours.
Highlighted Features:
1. The Ford F7TZ-12K073-B camshaft sensor is an efficient and reliable part.
2. It is easy to install and use.
3. The camshaft sensor is made to high quality standards.
4. It is a cost effective solution.
5. The camshaft sensor is backed by a warranty.
5. 1994-1996 7.3L Power Stroke Camshaft Position (CMP) Sensor – Alliant Power # AP63491 – OEM Part #’s: F4TZ12K073C DU87
The CMP sensor is a Hall-effect device that senses the position of the camshaft and sends a signal to the PCM. This signal is used to time the fuel injection and ignition events. The sensor is located on the front of the engine, just below the camshaft sprocket. The sensor has a single wire connector.
The CMP sensor is a critical component of the engine control system. The signal from the CMP sensor is used to determine when to fire the injectors and to time the spark events. If there is a problem with the CMP sensor, the engine may run rough, have poor performance, or not start at all.
This is the camshaft position (CMP) sensor for the 1994-1996 7.3L Power Stroke diesel engines. This sensor is a OEM part and is of the same quality as the original equipment.
Highlighted Features:
1. Alliant Power # AP63491 OEM Part #\’s: F4TZ12K073C, DU87
2. The sensor is a direct replacement for the factory unit
3. The sensor is easy to install
4. The sensor is made from high quality materials
5. The sensor is backed by a quality warranty
Buying Guide for best 7.3 camshaft position sensor
Buying Guide for best 7.3 camshaft position sensor:
If you’re in the market for a new camshaft position sensor, it’s important to take a number of factors into consideration before making your purchase. Here are some key things to think about:
The make and model of your vehicle: Not all camshaft position sensors will be compatible with every vehicle. It’s important to find one that is specifically designed for your car or truck.
The features offered: Some camshaft position sensors offer additional features, such as the ability to read and diagnose engine trouble codes. If you’re looking for a specific feature, be sure to check that the sensor you’re considering offers it.
The price: Camshaft position sensors can vary in price, so it’s important to find one that fits within your budget.
The reputation of the brand: When purchasing a camshaft position sensor, it’s important to consider the reputation of the brand.